Undervolting Averatec 2370 (Turion64x2) using RMClock

December 3, 2006 at 2:28 am 1 comment

Recently, I purchased an Averatec 2370 laptop with Turion64 x2 TL-50. I wondered if I could use RMclock to underclock and undervolt the Turion64 and what sort of effect it will have on the temperature and battery times.

First, I had to find out the Turioni64 x2 TL-50’s frequency and voltage range. I tried reading the literature on the AMD site, but it was hopelessly out of date. The white paper on the thermal characteristic is dated back to March 2006.

I launch RMClock and set it to monitor the voltage and frequency. I then open the Window’s Power Options object in Control Panel and set it to the following entry to “Always On”, which sets the computer to the highest frequency and voltage. I then set the power to “Max Battery”, which displays the lowest frequency and lowest voltage.

Configuration Frequency (Ghz) Voltage (V)
Minimum Power 0.804 0.800
Maximum Power 1.607 1.075

With that in mind, I ran RmClock, set the management to use Power Saving and set it to the smallest multiplier and voltage to 0.8V. I then ran CPU Burn and keep lowering the voltage. I managed to get it to below 0.700V before the computer crashed. I then set the management to Maximal performance and set it to the highest multiplier and the voltage of 1.075 v. I then keep lowering the voltage while running CPU Burn until the computer crash. I manage to get the voltage down to below 0.875V before the computer crashed. Finally, I set the management to Performance on Demand. I selected all of the multiplier and set the min and max voltage to the voltage to 0.700 V and 0.875 V. RmClock then adjust the immediate voltage from between low and high multiplier. Even though CPU Burn indicated a usable range of 0.7 – 0.875 v, the computer crashed when I attempted to install at 0.7 v. I upped the low end voltage to 0.712 v and the problem went away.

When I set management to “Performance On Demand”, the computer crashed. It turned out that half-step transitions is not allowed. Make sure you have the option unchecked in the Advance CPU Settings, P-Transitions Tab.

I then ran a test where I ran two copies of CPU-Burn (since we have two core, I needed to run 2 programs to get 100% cpu usage) and with wireless off. The computer is set to ran at the highest speed possible. The only difference between normal and undervolt is that normal runs at the default voltage of 1.075v while undervolt ran at the lower voltage of 0.875 v.

Configuration CPU Freq (Ghz) CPU Voltage (V) Battery Life (hours) CPU Temperature (C)
Normal 1.6 1.075 0:49 70
Undervolt 1.6 0.875 1:12 56

I was surprised by how much the temperature dropped when I reduced the voltage by 0.2 volts. By undervolting, one can extend battery life, reduce heat, while getting the same performance. This is a free lunch.

Undervolting potential will vary from chip to chip, so you’ll have to experiment to see how low you can go.

Advertisements

Entry filed under: Undervolting.

Internet Explorer 7 hangs on Startup After installation Intel Core Duo T2250 vs. Turion64x2 TL-50

1 Comment Add your own

  • 1. RB  |  January 8, 2007 at 12:00 pm

    I just got an Averatec 2370 and I’m trying to follow along with your procedure (to see what voltages my own CPUs can take) however RMclock is a little confusing — there seems to be many places where I can change the settings. Also, it’s not clear what the point of chosing “power savings” or “performance” since it seems like in any case the voltage range is always te same? For the naive newbies like me, could you be a bit more specific as to under which sections/tabs you changed your values? Maybe a even a screen capture or two to help illustrate would go a long way… but maybe that’s asking too much? 🙂

    Reply

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Trackback this post  |  Subscribe to the comments via RSS Feed


Calendar

December 2006
M T W T F S S
« Nov   Jan »
 123
45678910
11121314151617
18192021222324
25262728293031

Most Recent Posts


%d bloggers like this: